Category Archives: Product Spotlights

Baryonyx “Arctic Fox” Scythe Stone

A beautiful ice blue scythe stone made for us in the USA to our specifications. 400 grit aluminum oxide with a medium-hard bond, this stone produces a finer edge than one might expect for its grit rating. Cuts fast, holds water well, resists glazing, is hard enough to bear down to realign rolled edges, and produces a very keen edge that easily dry shaves while retaining the “sticky” bite of a medium or coarse stone. Finer than any of our other scythe stones, yet no slower to hone with. We’re very impressed, and it’s exceeded our expectations for performance.


With stock crisp edges:



With dressed edges:

IMG_5465 IMG_5466 IMG_5467 IMG_5468

Restoration: Seymour No.2 Bush Snath

A professionally restored Seymour No.2 bush snath outfitted with a new old stock Swedish-made Banko bush blade. The Seymour No.2, now long discontinued, was similar to the still-produced No.1 grass snath but with a thicker end diameter and a four-hole heel plate rather than three. The holes are arranged in a “♦” shape rather than the “▼” arrangement on the No.1. Some older examples of this snath have capped nibs, with a three-pronged, domed, circular brad having been driven into the top of the nib to cover the recessed nut and projecting thread of the nib iron.

SeymourNo2Snath1 SeymourNo2Snath2 SeymourNo2Snath3 SeymourNo2Snath4 SeymourNo2Snath5 SeymourNo2Snath6 SeymourNo2Snath7

A Traditional “Rag Knife”

A traditional style of farm knife made from a broken American scythe blade, usually used for topping root crops.

The blade below crack was cut back to the spine, which was forged out into a tang. Normally this would have been simply wrapped with rags to form the grip (which is why they were called rag knives) but we used a reshaped billhook handle instead.

The tang is peened on the end and the grip tightly wedged from the top inside the ferrule for an extremely tight and secure fit.

A Rag Knife A Rag Knife A Rag Knife A Rag Knife

Vintage American Scythe–Offset Seymour Ironclad

A fully restored and tuned Seymour Ironclad swing socket snath outfitted with an Emerson & Stevens “Clipper” grain cradle blade adapted for haying use. The snath has been significantly shaved down, the nib blocks replaced with ones of improved fit (the upper one having been modified for proper interface) and new grips installed on the original nib irons. The hardware has been electrolytically de-rusted and thoroughly cleaned, the whole tool having been given a protective clear coating.

IMG_1682 IMG_1684 IMG_1687 IMG_1688 IMG_1693 IMG_1695 IMG_1696 IMG_1700 IMG_1702 IMG_1705 IMG_1707


Solving the Tomahawk Handle Knob Problem

Shown here is a 350g Rinaldi “Calabria” hand axe with a modified handle. A common complaint raised regarding slip fit handles is that (despite their virtues) a knob is either small or totally absent, meaning there is little or nothing to stop the hand from slipping off the end of the handle if a loose grip is used. A simple tapered cross-pin at the end of the handle creates a removable solution to this problem.

A tapered hole was bored with a small step drill and a wooden pin, tapered to match, driven into the hole. The single-sided pin with the projection to the outside of the hand is the most comfortable and secure arrangement vs. a finger-sided or double-sided projection, and if the head must be removed from the handle for use as an independent tool the wooden pin is easily driven out so it does not obstruct the removal of the head. This provides several notable advantages over the use of a lanyard: the user’s hands may slide freely along the handle as needed to adjust grip position, the handle may still be immediately released in the event of an emergency or accident, and the pin allows  the end of the handle to be tucked under a belt and have it stay there nicely if the user’s hands need to be free without setting the axe on the ground.

Right Side Left Side Left Side of Pin Pin viewed with the bit of the axe facing the viewer. Pin viewed with the bit of the axe facing away from the viewer. Angled detail view, right side. Angled detail view, left side.